mirror of
https://github.com/grillbaer/esp32-geiger-counter.git
synced 2025-12-24 14:31:44 +01:00
32 lines
2.9 KiB
Markdown
32 lines
2.9 KiB
Markdown
[](https://travis-ci.org/grillbaer/esp32-geiger-counter)
|
|
|
|
# IoT Geiger Counter with ESP32, OLED Display and Thingspeak Channel
|
|
|
|
- Measures radioactive gamma and beta radiation with quite good resolution at the typical low levels of the natural radiation (due to the big STS-6 tube)
|
|
- Displays the current counts per minute (CPM), estimated dose equivalent rate in micro-Sievert per hour (µS/h) and 10 minutes history with 5 second resolution as bargraph
|
|
|
|
- Low-power mode for use with batteries, OLED display and click sounds on, WiFi off
|
|
- WiFi mode for thingspeak data upload every minute, see https://thingspeak.com/channels/758223
|
|
[](https://thingspeak.com/channels/758223)
|
|
|
|
Feel free to use this project as a base for your own projects AT YOUR OWN RISK!
|
|
|
|
# Hardware
|
|
|
|
- Russian Geiger counter tube STS-6 (CTC-6) at 400 V with ~5 MΩ series resistor
|
|
- High voltage circuit from ArnoR at mikrocontroller.net https://www.mikrocontroller.net/topic/380666, schematic https://www.mikrocontroller.net/attachment/273334/HystereseStepUpTLC555-2.png. *Keep the high-voltage capacitor small to avoid dangerous charges! For safety avoid any contact with the high voltage parts!*
|
|
- ~400 µs pulse generation using Geiger tube series resistors as voltage divider, high impedance input to darlington transistor and TLC 555 timer for rectangle pulse generation
|
|
- ESP32 board Wemos Lolin32
|
|
- OLED 128x64 with controller SH1106 at I2C
|
|
- Voltage supply from either USB or power supply or 3x 1.5V AAA batteries, circuit works stable from 3.0 V up to 5.0 V
|
|
- Pulse input is expected at GPIO 18 (high pulses with at least about 250 µs length)
|
|
- Switch for WiFi mode is expected at GPIO 4 (low=WiFi mode, high=low-power mode)
|
|
- OLED I2C bus is expected at GPIO 22 (SCK) and 21 (SDA)
|
|
|
|
# Software
|
|
|
|
- [PlatformIO VSCode project](https://github.com/platformio/platformio-vscode-ide) using [Arduino](https://github.com/arduino/Arduino) library, [Espressif ESP-IDF](https://github.com/espressif/esp-idf) for sleep functions and [U8g2](https://github.com/olikraus/u8g2) for display output
|
|
- Low-power mode uses light sleep, a wake-up for each signal pulse change and a wake-up every 1000 ms to update pulse statistics and OLED. This results in about 90% sleep. Could be improved using deep sleep and ULP. However, light sleep is already quite good and much easier.
|
|
- WiFi mode uses no sleep and simple interrupts for pulse counting. Pulse statistics and OLED are updated every 1000 ms, data is sent to thingspeak every 60 s.
|
|
- Credentials (WiFi SSID, password, thingspeak channel key) are declared in `credentials.h` and defined with dummy values in `credentials.cpp`. Define them in a sibling file named `secret_credentials` (which is never committed) and uncomment its include in `credentials.cpp`
|