mirror of
https://github.com/yuriskinfo/cheat-sheets.git
synced 2025-12-21 21:33:25 +01:00
66 lines
2.7 KiB
Plaintext
66 lines
2.7 KiB
Plaintext
= Fortigate SD-WAN debug and verification commands cheat sheet
|
|
Yuri Slobodyanyuk <admin@yurisk.info>
|
|
v1.0, 2021-02-18
|
|
:homepage: https://yurisk.info
|
|
|
|
Yuri Slobodyanyuk, https://yurisk.info
|
|
|
|
|
|
== SD-WAN verification and debug
|
|
[cols=2, options="header"]
|
|
|===
|
|
|Command
|
|
|Description
|
|
|
|
|*diagnose sys sdwan health-check* (6.4 and newer)
|
|
|
|
*diagnose sys virtual-link health-check* (5.6 up to 6.4)
|
|
|
|
| Show state of all the health checks/probes. Successful probes are marked `alive`, failed probes are marked `dead`. Also displays `packet-loss, latency, jitter` for each probe.
|
|
|
|
|*diagnose sys sdwan member* (6.4 and newer)
|
|
|
|
*diagnose sys virtual-wan-link member*
|
|
|
|
|Show list of SD-WAN zone/interface members. Also gives each interface gateway IP (if was set, 0.0.0.0 if not), `priority`, and `weight` both by default equal `0`, used with some SLA Types.
|
|
|
|
|*diagnose sys sdwan service* (6.4 and newer)
|
|
|
|
*diagnose sys virtual-wan-link service*
|
|
|
|
|List configured SD-WAN rules (aka `services`), except the Implied one which is always present and cannot be disabled, but is editable for the default load balancing method used. Shows member interfaces and their status `alive` or `dead` for this rule.
|
|
|
|
|
|
|
|
|*diag sys sdwan intf-sla-log <interface name>* (6.4 and newer)
|
|
|
|
*diag sys virtual-wan-link intf-sla-log <interface name>*
|
|
|
|
|Print log of <interface name> usage for the last 10 minutes. The statistics shown in bps: `inbandwidth`, `outbandwidth`, `bibandwidth`, `tx bytes`, `rx bytes`.
|
|
|
|
|
|
|*diag netlink interface clear <interface name>*
|
|
|
|
|Clear traffic statistics on the given interface, this resets statistics of the SD-WAN Monitor GUI widget for this interface as well. Needed, if, for example, you changed SD-WAN rules, but not sure if it's already active. E.g. `diag netlink interface clear port1`.
|
|
|
|
|
|
|*diagnose firewall proute list*
|
|
|List ALL Policy Based Routes (PBR). SD-WAN in Fortigate, after all, is implemented as a variation of PBR. This command lists manual (classic) PBR rules, along with SD-WAN created via SD-WAN rules. *Important*: Manually created PBR rules (via `Network -> Policy Routes` or on CLI `config route policy`) always have preference over the SD-WAN rules, and this command will show them higher up.
|
|
|
|
|*diagnose debug flow filter*
|
|
|
|
*diagnose debug flow filter <filtering param>*
|
|
|
|
*diagnose debug flow show function-name enable*
|
|
|
|
*diagnose debug flow trace start [number]*
|
|
|
|
*diagnose debug enable*
|
|
|
|
|Use `diagnose debug flow` to see how the traffic is being routed via SD-WAN. Look for something like `Match policy routing id=2131951617: to 10.10.10.13 via ifindex-3` and `out port1 vwl_zone_id 2, state2 0x1,` here `id=2131951617` is the SD-WAN PBR rule id as seen in `diagnose firewall proute list` and `vwl_zone_id 2` is the SD-WAN zone in the list of virtual-links.
|
|
|
|
|
|
|
|
|
|
|===
|