diff --git a/README.md b/README.md
index 4c22f9d..f479c04 100644
--- a/README.md
+++ b/README.md
@@ -4,8 +4,44 @@
Jamming is ILLEGAL! Educational purposes only!
+
+
+
## ESP32-BlueJammer
The ESP32-BlueJammer (Bluetooth jammer, BLE jammer, WiFi jammer, RC jammer) disrupts various devices using an ESP32 and nRF24 modules, causing plenty of noise and sending unnecessary packets (DoS).
@@ -28,14 +64,14 @@ This PCB can fit an ESP32 DevKit and 2 RF-modules such as nRF24 or CC1101 etc.,
For this one, all you need is listed below:
**Required:**
-- ESP32 Dev Module (such as ESP32-WROOM-32U, any ESP32 should work as long as it has the needed pins, 38P is recommended!)
-- nRF24L01+PA+LNA (2x)
+- **[ESP32 Dev Module](https://s.click.aliexpress.com/e/_onYIVKr)** (**Recommended: ESP32-32U CP2102**, any ESP32 should work as long as it has the needed pins, 38P required!)
+- **[nRF24L01+PA+LNA](https://s.click.aliexpress.com/e/_oma5UQx)** (2x) (**Choose: LNANRF24**)
**Additional:**
-- TP4056 Charging Module (Micro-USB/Type-C)
-- JST PH 2.0 Connector
-- 3.7V Li-Ion Battery
-- 3rd Antenna: IPEX to SMA-F pigtail
+- **[TP4056 Charging Module (Micro-USB/Type-C)](https://s.click.aliexpress.com/e/_on7Lkvh)**
+- **[JST PH 2.0 Connector](https://s.click.aliexpress.com/e/_ooSOhDd)**
+- **[3.7V Li-Ion Battery](https://s.click.aliexpress.com/e/_on04mQ7)**
+- **[3rd Antenna: **IPEX to SMA-F pigtail](https://s.click.aliexpress.com/e/_oFDpn1V)**
[Shop](https://datechlabs.com/products/blue-esp-diy-pcb-back-order)
@@ -45,8 +81,8 @@ For this one, all you need is listed below:
This is an ESP32 with RF-module breakouts (nRF24/CC1101 etc.) for experimenting. ***Remember: It is not intended for illegal use, neither for my project!***
**Required:**
-- nRF24L01+PA+LNA (2x)
-Why do you need to get the nRF24's? -> the pinout can be used to connect either nRF24 or CC1101 modules for further experiments with and ESP32 chip.
+- **[nRF24L01+PA+LNA](https://s.click.aliexpress.com/e/_oma5UQx)** (2x) (**Choose: LNANRF24**)
+Why do you need to get the nRF24's? -> the pinout can be used to connect either nRF24 or CC1101 modules for further experiments with an ESP32 chip.
[Shop](https://datechlabs.com/products/the-blue-esp-pre-order)
@@ -92,31 +128,33 @@ Why do you need to get the nRF24's? -> the pinout can be used to connect either
## Hardware - Make your own ESP32-BlueJammer
-
+(Aliexpress affilate links to support me-linked to the item names)
### Required:
-- **ESP32 Dev Module** (such as ESP32-WROOM-32U, any ESP32 should work as long as it has the needed pins, 38P is recommended!)
-- **nRF24L01+PA+LNA** (2x)
-- **10uF Capacitor** (2x) (any voltage above 5V)
-- **Prototype PCB** (at least 7x9 cm, but you will need to cut it down to fit the 3D-printed case, which fits a size of 7x5,5cm!)
+- **[ESP32 Dev Module](https://s.click.aliexpress.com/e/_onYIVKr)** (**Recommended: ESP32-32U CP2102**, any ESP32 should work as long as it has the needed pins, 38P required!)
+- **[nRF24L01+PA+LNA](https://s.click.aliexpress.com/e/_oma5UQx)** (2x) (**Choose: LNANRF24**)
+- **[10uF Capacitor](https://s.click.aliexpress.com/e/_oFvFeYX)** (2x) (any voltage above 5V)
+- **[Prototype PCB](https://s.click.aliexpress.com/e/_oBtd18j)** (at least 7x9 cm, but you will need to cut it down to fit the 3D-printed case, which fits a size of 7x5,5cm!)
### Additional:
-- 3rd Antenna: **IPEX to SMA-F pigtail**
-- Status LED: **3mm LED**
-- **4.7k Ohm Resistor**
+- [3rd Antenna: **IPEX to SMA-F pigtail](https://s.click.aliexpress.com/e/_oFDpn1V)**
+- [Status LED: **3mm LED](https://s.click.aliexpress.com/e/_ooxufHV)**
+- **[4.7k Ohm Resistor](https://s.click.aliexpress.com/e/_oBV1Q1Z)**
### If you're looking to add a battery:
-- **3.7V Li-Ion Battery**
-- **JST PH 2.0 Connector**
-- **TP4056 Charging Module (Micro-USB/Type-C)**
-- **Mini Slide Switch**
+- **[3.7V Li-Ion Battery](https://s.click.aliexpress.com/e/_on04mQ7)**
+- **[JST PH 2.0 Connector](https://s.click.aliexpress.com/e/_ooSOhDd)**
+- **[TP4056 Charging Module (Micro-USB/Type-C)](https://s.click.aliexpress.com/e/_on7Lkvh)**
+- **[Mini Slide Switch](https://s.click.aliexpress.com/e/_ooC8DXh)**
### To screw the 3D printed case together you must have:
- **M3x16 Screws** (2x)
-- **M3 Nuts** (2x)
+- **M3 Nuts** (2x)
+Get this M3 kit instead:
+- **[M3 screws&nuts kit](https://s.click.aliexpress.com/e/_oC24YXH)**
@@ -141,6 +179,11 @@ I've created a webflasher to make it super easy for you to flash your ESP32 chip
- Choose your firmware, chip and connect
- Flash the firmware of your choice :D
+## Flashing ESP32 via binary files
+- Download the **.bin files** available on this repository
+- Use any flasher of your choice
+- Flash it :D
+
If your ESP32 is not showing up in the device list or won't get recognized you will need to have [THESE DRIVERS INSTALLED](https://www.silabs.com/documents/public/software/CP210x_Windows_Drivers.zip) which can be found on my [Discord server](https://discord.gg/yNGhKxzqUE) too!
@@ -193,6 +236,15 @@ Here are both pinouts for HSPI and VSPI. You need both nRF24L01 modules connecte
+
+## PCB
+
+That's how the components are placed (PCB size=7cm x 5.5cm - Larger sizes will NOT fit in the case!)
+
+
+
+
+
## 3D printed case
#### The 3D printed case fits ONLY a PCB size of 7cm x 5.5cm and you'll need to drill out 2 holes according for the M3 screws to fit through the PCB!
Access to the ESP32 micro-USB port, aswell as to both EN & Boot buttons
@@ -225,14 +277,6 @@ Here are both pinouts for HSPI and VSPI. You need both nRF24L01 modules connecte
-## PCB
-
-That's how the components are placed (PCB size=7cm x 5.5cm - Larger sizes will NOT fit in the case!)
-
-
-
-
-
## About the ESP32-BlueJammer and my source code
- **Is my ESP32-BlueJammer really working?**
Yes! My ESP32 BlueJammer is fully functional, and no one pauses the sound in the demo video. Many people have built their own ESP32-BlueJammer and confirmed that it works! Join my Discord and see for yourself! ;D
+
+
+ 
+
+
+ 
+
+
+ 
+